
Accredited ISO 17025 calibration certificate for these 30446-0017 500 lb force gauges with hardened ball force tools is be available on request (for an extra charge). Why Calibrate?
Proven accuracy and ruggedness sets our mechanical force gauge apart in the force measurement industry. The Dillon X-C force gauges measure tension, compression or push/pull force. The "D" shaped deflection beam is the heart of the Force Gauge system. Highly engineered materials with close machining tolerances and proper heat treatment provide optimum strength and spring characteristics. All models feature accuracy of ±1% of full capacity, except the 25,000 (10000 kg) capacity instruments which are accurate to ±2% of full capacity. Ideal for stand alone force applications or as the load defining component of a much larger system.
Load is applied against a hardened ball which rotates to maintain vertical alignment as pressure increases. The ball is held in place with a spring clip or retainer. A threaded mounting hole is located opposite the loading ball in the bottom of the beam. Model X-C is available in pound, kilogram or Newton capacities.
1. Deflection beam
2. Dial indicator with zero at standard 12:00 position.
3. Bezel
4. Maximum load pointer (optional)
5. Pressure button
6. Slanted Anvil
7. Dial indicator plunger
8. Anvil set screw
9. Mounting bracket for dial indicator
10. Screws for mounting bracket
11. Bezel-locking screw
12. Loading ball
13. Spring retainer clip
A D-shaped deflection beam is the heart of the Dillon Force Gauge. Machined to close tolerances, beams are heat treated to develop optimum strength and spring characteristics. High-strength aluminum is used in Model X instruments through 500 lb (200 kg). Ranges above this are fabricated from aircraft-quality alloy steel. A precision dial indicator is mounted at the null point of the deflection beam. The indicator plunger rests against a slanted anvil at the open end of the beam, as shown in the photo. Under compression loads, the two halves of the beam tend to close. Tension force causes them to move apart. This action pushes the plunger inward, as determined by the slant of the anvil. Readings produced on the dial are in direct relation to applied load. The pointer revolves 360° clockwise under compression or tension forces. Push-pull gauges read half scale (180°) clockwise in compression, and counterclockwise, 180° from center zero under tension loads.
Accidental overloads up to 30% of capacity can be safely sustained without injury to the dial indicator or deflection beam. All capacities feature a 5:1 design safety factor.
When measured across the center of top- and bottom-loading holes, the approximate beam deflection is as follows:
Dillon X-C Compression Force Gauge (series) | Accuracy | Capacity & Dial |
30386-0035 | ±1% of full scale | 50 lb x 1/2 lb |
30386-0043 | 100 lb x 1 lb | |
30446-0033 | 250 lb x 2-1/2 lb | |
30446-0017 | 500 lb x 5 lb | |
30444-0019 | 1,000 lb x 10 lb | |
30388-0017 | 2,000 lb x 20 lb | |
30389-0016 | 5,000 lb x 50 lb | |
30423-0014 | 10,000 lb x 100 lb | |
30449-0014 | ±2% of full range | 25,000 lb x 250 lb |
Forcegauges.ca is your fast, easy-to-use website for quality force instruments available for almost any industries to measure the force during a push or pull test. We offer over 500 force gages and force sensors from most valuable brands, ready to be shipped from our Brampton (Toronto area) warehouse.
All prices in this website reflect net cost to you in Canadian dollars and does not include calculated shipping costs. Currently we accept credit card payments. However, you can submit your payment via cheques, wire transfers and purchase orders on approved credit.